UK to Require Melt-and-Pour Reporting for Steel Imports
The UK will require importers of certain steel products to report the country where the steel was first melted and poured from July 1, 2027, adding a new traceability requirement to the country's tighter steel import regime.
- Voluntary melt-and-pour reporting begins April 1, 2027.
- Reporting becomes mandatory July 1, 2027.
- The rule applies to steel within the scope of the UK steel trade measure.
- Declarations valued below £2,000 are exempt.
- Mill test certificates are the government's preferred supporting evidence.
MONTREAL (SteelPrices): UK steel importers will soon need to know more than where their material was shipped from or last processed.
Beginning July 1, 2027, importers of steel covered by the UK's trade measure must declare the country where the material was first melted and poured.
The requirement will first operate on a voluntary basis from April 1 through June 30, giving importers, suppliers and customs intermediaries three months to prepare.
The information will be submitted through the UK's Customs Declaration Service, or CDS.
Melt and Pour Is Different From Country of Origin
The UK government makes an important distinction between the country of melt and pour and the declared country of origin.
The country of melt and pour is where the steel was first melted and poured during the initial steelmaking stage.
The country of origin, by contrast, can reflect where the product was later substantially transformed.
A steel product may therefore be processed, rolled or finished in one country even though the underlying steel was originally melted and poured somewhere else.
Importers should not assume that the country of origin automatically identifies the country of melt and pour.
What UK Steel Importers Need to Change Before July 2027
This is not a new tariff. It is a documentation and traceability requirement that will change what buyers need from mills, traders and customs agents.
- Ask suppliers: for the country of melt and pour
- Update purchase orders: include melt-and-pour information requirements
- Keep evidence: mill certificates, quality documents or approved alternatives
- Coordinate with agents: ensure customs intermediaries can report through CDS
- Update systems: store the required documentation for HMRC inspection
The key operational issue is traceability. Importers that wait until the steel arrives may find it difficult to obtain original melt-and-pour data, especially for material ordered months earlier.
That is why the government is encouraging companies to begin collecting the information now and to use the voluntary reporting window as a test period before the rule becomes mandatory.
Mill Test Certificates Are the Preferred Evidence
The UK government identifies mill test certificates as the preferred supporting document.
Where available, the certificate should state the country of melt and pour and the relevant heat number identifying the batch of steel.
If a mill test certificate is unavailable or incomplete, importers may use alternative or supplementary records.
Accepted evidence can include invoices, delivery notes, quality certificates, purchase-order clauses, supplier declarations, production records, customs documents from the exporting country and commercial correspondence.
The supporting documentation must still provide the required country of melt and pour and heat information.
Small Import Declarations Are Exempt
Declarations under the same commodity code and country of origin with a value below £2,000 are exempt from the new melt-and-pour requirement.
In those cases, importers will not be required to complete the relevant CDS declaration or retain supporting melt-and-pour evidence for that requirement.
Imports into Northern Ireland are subject to separate arrangements under the Windsor Framework, and existing requirements there remain unchanged.
The Rule Covers Steel Under the UK's New Trade Measure
The melt-and-pour requirement applies to products within the scope of the UK's steel trade measure introduced on July 1, 2026.
Under that regime, the UK reduced overall tariff-free steel import quotas by 51% compared with the previous safeguard system.
The final annual quota volume was set at approximately 3.2 million tonnes.
Steel imported above the applicable quota is subject to a 50% duty.
The measure applies to covered products that can be produced in the UK.
SteelPrices policy note: The reporting requirement does not itself change tariff rates, quota allocations or the rules used to determine country of origin. It adds another information requirement to covered imports.
Also Read
- UK to Cut Steel Import Quotas, Raise Tariffs to Protect Domestic Industry
- UK Steel Power Costs to Hit £91/MWh, 49% Above France
Why the UK Wants More Steel Traceability
The government says the requirement is intended to improve transparency in steel supply chains and strengthen its understanding of global steel overcapacity.
That information could become relevant to future trade-policy decisions because the country where steel was originally produced may be different from the country from which the finished product is ultimately exported.
The UK said melt-and-pour reporting is becoming more common among economies concerned about global excess steel capacity, pointing to existing practices in the EU, United States and Canada.
The policy also follows commitments made by participating countries at the Global Forum on Excess Steel Capacity ministerial meeting in September 2026.
HMRC Can Check Supporting Records
The system will operate on a "declare and retain" basis.
Importers will declare the country of melt and pour and identify the type of evidence they hold, while keeping the underlying records available for inspection.
HM Revenue and Customs may check declarations through its normal compliance procedures, including post-clearance audits.
Incorrect or incomplete declarations may be subject to standard civil penalties once the mandatory system is in force.
Even during the voluntary period, companies choosing to report must retain evidence supporting the information they declare.
What Steel Buyers Should Do Now
The government's guidance is clear that companies should not wait until July 2027 to begin preparing.
Importers are being encouraged to request melt-and-pour information from suppliers now, include the requirement in new purchase orders and contracts, coordinate with customs agents and make sure internal systems can retain the relevant records.
This is especially important for steel ordered four to six months in advance, because obtaining melt-and-pour information retrospectively may be difficult once the material is already in transit or delivered.
For UK steel buyers, traders and service centers, the practical impact will therefore be felt well before mandatory reporting officially begins.
Sources: UK Department for Business, Innovation, Science and Trade; HM Revenue and Customs.
Explore More

